[elrepo] [elrepo-devel] Broken kmod-compat-wireless package

[Phil Perry]

On 14/08/12 13:17, Roy Bonser wrote:
> That did the trick, thanks!
>
> dmesg:
> cfg80211: Calling CRDA to update world regulatory domain
> cfg80211: World regulatory domain updated:
> cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,
> max_eirp)
> cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> b43-phy0: Broadcom 4331 WLAN found (core revision 29)
> b43-phy0 debug: Found PHY: Analog 9, Type 7, Revision 1
> b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2059, Revision 0
> Broadcom 43xx driver loaded [ Features: PMNLS ]
> ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> Registered led device: b43-phy0::tx
> Registered led device: b43-phy0::rx
> Registered led device: b43-phy0::radio
> cfg80211: Calling CRDA for country: US
> cfg80211: Regulatory domain changed to country: US
> cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,
> max_eirp)
> cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
> cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
> cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
> cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
>
> b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
> b43-phy0 debug: Chip initialized
> b43-phy0 debug: 64-bit DMA initialized
> b43-phy0 debug: QoS enabled
> b43-phy0 debug: Wireless interface started
> b43-phy0 debug: Adding Interface type 2
> ADDRCONF(NETDEV_UP): wlan0: link is not ready
>
>
> The wireless shows up in the Network Manager applet now and I was able to
> join the network.
>
>    --Roy
>

Brilliant!

Thanks Roy, I'll get updated packages built that add the missing udev rules.

Many thanks for your testing.

Regards,

Phil