[elrepo] atl1e driver issue

[Newt]

On 18/05/2012 08:13, Ljubomir Ljubojevic wrote:
> On 05/17/2012 10:21 PM, Newt wrote:
>> Hi,
>>
>> I'm running Centos 6.2 and I'm trying to get the atl1e driver to work
>> (I've confirmed using the adive on the ElRepo website that that's correct).
>>
>> I've downloaded kmod-atl1e-1.0.1.14-1.el6.elrepo.x86_64.rpm and added it
>> to the Centos box using rpm -Uvh
>> kmod-atl1e-1.0.1.14-1.el6.elrepo.x86_64.rpm.
>>
>> What do I need to do now? I've rebooted (a few times) but ifconfig only
>> gives me lo as a device and not eth0.
>>
>> Sorry if I'm asking a foolish question.
>>
>> Thanks,
>>
>> Newt
>> _______________________________________________
>> elrepo mailing list
>> elrepo at lists.elrepo.org
>> http://lists.elrepo.org/mailman/listinfo/elrepo
>>
>>
> running lspci -nnvv should give you listing where you can see kernel
> module used for each device. Check what, if any module is used.
>
Well, that looked promising.

03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 
v2.0 Gigabit Ethernet [1969:1083] (rev c0)
     Subsystem: Giga-byte Technology Device [1458:e000]
     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
     Latency: 0, Cache Line Size: 4 bytes
     Interrupt: pin A routed to IRQ 16
     Region 0: Memory at fbdc0000 (64-bit, non-prefetchable) [size=256K]
     Region 2: I/O ports at ef00 [size=128]
     Capabilities: [40] Power Management version 3
         Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
         Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
     Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
         Address: 0000000000000000  Data: 0000
     Capabilities: [58] Express (v1) Endpoint, MSI 00
         DevCap:    MaxPayload 4096 bytes, PhantFunc 0, Latency L0s 
unlimited, L1 unlimited
             ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- 
Unsupported-
             RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
             MaxPayload 128 bytes, MaxReadReq 512 bytes
         DevSta:    CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ 
TransPend-
         LnkCap:    Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, 
Latency L0 unlimited, L1 unlimited
             ClockPM+ Surprise- LLActRep- BwNot-
         LnkCtl:    ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- 
CommClk+
             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
         LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
     Capabilities: [6c] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Connection timed out
         Not readable
     Capabilities: [100] Advanced Error Reporting
         UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
         UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
         UESvrt:    DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
         CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout+ NonFatalErr-
         CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
         AERCap:    First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
     Capabilities: [180] Device Serial Number ff-46-70-f0-50-e5-49-ff
     Kernel driver in use: atheros_eth
     Kernel modules: atl1e

However there is a read failed error just above - I'm not sure what that 
is implying...

Any suggestions?

N.